BendPak

Four published lock heights, so the car sits where the job wants it A low-rise lift that only goes up and down is a jack with ambitions. The B...

74.4 in. long, and none of it above the floor The BendPak P-9000LTF is the flush-mount member of this low-rise family, and the number that exp...

BendPak PL-6KT Triple Independent Platform Parking Lift Most parking lifts leave the car underneath sitting below a pair of open runways, whic...

BendPak PCL-18B-2 Mobile Column Lifts, Pair — High Voltage Read this first, because it is the thing most likely to cause a bad purchase: a pai...

BendPak PCL-18B-2 Mobile Column Lifts, Pair — Low Voltage The feature on these columns that nobody thinks about until they need it is the manu...

BendPak PCL-18B-4 Mobile Column Lifts, Set of Four — High Voltage The thing that separates these columns from a screw-drive mobile lift is whe...

BendPak PCL-18B-4 Mobile Column Lifts, Set of Four Four columns is the standard working set, and BendPak's cabling is the reason this configur...

BendPak PCL-18B-6 Mobile Column Lifts, Set of Six The PCL-18B-6 is a six-column mobile lifting system for three-axle trucks, buses, refuse veh...

BendPak PCL-18B-6 — Six Columns, Built From Parts You Can Buy Here is the detail on this lift that almost no competing column set can match, a...

BendPak PCL-18B-8 — Eight Columns, or Two Independent Fours The argument for eight columns is not really the biggest vehicle you can lift. It ...

BendPak PCL-18B-8, Low Voltage — the Eight-Column Set for a Standard Shop Supply This package exists for a specific and very practical reason:...

PL-12000DP: two parking platforms that rise and lower independently The most useful fact about the PL-12000DP is sitting halfway down the manu...

PL-12000DPS: the triple-stack idea, sized for a garage with an ordinary roof Every stacking parking lift asks the same question first, and it ...

It uses no motor power at all on the way down The PL-6000DC lowers on gravity. The platform's own weight drives the descent through the hydrau...

The One With an Adjustable Support Base — 45.75" to 59" The specification that sets the BendPak RBJ15000 apart from the rest of the rolling b...

Rated for More Than Half the Vehicle — Which Is the Only Way to Handle an Offset Load The BendPak RBJ18000 is an 18,000 lb rolling bridge jac...

A Pair of These Covers a 50,000 lb Vehicle — the Reason This Model Exists The BendPak RBJ25000 is the highest-capacity rolling bridge jack in...

BendPak RJ45LP Low-Profile Rolling Bridge Jack LP is for low profile, and on this jack it is not a styling word. The pads sit 4.25" (108 mm) a...

BendPak RJ45W Rolling Bridge Jack The RJ45W is the way into wheel-free service for shops and home garages running BendPak's smaller four-post ...

BendPak RJ6W Rolling Bridge Jack Among BendPak's rolling bridge jacks, the RJ6W is the one that gets out of the way. Its pads sit just 1.25" (...

BendPak RJ7W Rolling Bridge Jack A four-post lift is superb at getting a vehicle in the air and hopeless at getting its wheels off the ground ...

Product Description BendPak RJ9W Rolling Bridge Jack The RJ9W is the heavy end of BendPak's rolling bridge jack range: an air-hydraulic jack t...

When it is down, the floor is just floor The SP-7XEF is the flush-mount member of this scissor family, and the whole argument for it is what y...

The scissor lift with nothing running across the middle Almost every scissor lift ties its two frames together with a cross member. It is the ...