All Products

iDeal RAJ-7K-L: the air supply is the specification to check first A rolling bridge jack is one of the few pieces of shop equipment that can b...

iDEAL iMobile MSC-6KLP: a 6,000 lb lift that never touches your floor Every other lift on this site is a building decision. Anchors, slab thic...

Product Description The open-frame version: no cabinet, so the space under the top is yours The iDeal PWB-1600 is the plain bench in this fami...

iDeal RAJ-7K-H: two mechanical lock positions, so the load is not resting on air The RAJ-7K-H is a 7,000 lbs pneumatic-over-hydraulic scissor ...

Levelling legs are the reason this bench works on a real shop floor Most catalogue benches assume a flat floor. Almost no working garage has o...

iDEAL PTDT-PW-1000: a tear-down bench with a 3.5 gallon parts washer that retracts into it The reason to buy this table rather than a bench an...

iDEAL TP10KAC-DX: the two-post whose arm set is published in full On a two-post lift the arms decide almost everything — whether a low car can...

Product Description iDEAL PSB-PSMTD: the mixing table that rolls, with the masking station built into it Most paint-room benches are fixtures....

Product Description MSC-13K-B-226: Siemens control gear on a 26,000 lbs mobile column set Mobile columns live or die on synchronisation, and i...

Product Description FP14KAC-X: the alignment-ready FP14, and what the "AC" adds This is the alignment configuration of iDEAL's 14,000 lbs four...

iDEAL TC-400M-B-PL230-K-BLK: the assist arm is the reason this configuration exists Anyone who has fought a stiff-sidewall powersport tyre kno...

Product Description FR-77T-18: the same 7,700 lbs rack, in a bench that fits a shorter bay The FR-77T-18 is not a smaller machine. It is the s...

iDEAL PSB-SDD26B-AK side down draft spray booth This is the wide one. At 17'-8" across the outside, the PSB-SDD26B-AK gives up roughly three ...

iDEAL A-2200IEH-XR: six lock heights, on a bench narrow enough for a real bay Most lift benches give you two useful heights: down, and up. The...

Product Description iDEAL U-2200IEH-XR: the ramp is as wide as the bench, and it folds away Loading is where most bench lifts are annoying. A ...

iDEAL TLX-7000: a 7,000 lbs lift with no hydraulics, no power unit and no compressor Almost every low-rise lift on the market is a hydraulic ma...

iDEAL PTDT-1000: 2.38mm steel rated for 1,000 lbs, with the drain built in This is the tear-down bench for a shop that already owns a parts wa...

iDEAL MSC-18K-X-6108 Mobile Column Lift - Set of Six Six columns can stand up to 32'8" apart. That single figure is what separates this set f...

iDEAL MSC-18K-X-472 Mobile Column Lift - Set of Four Every column in this set locks by itself and stops by itself. There is an independent me...

MSC-18K-X-236: a 36,000 lbs column pair that runs off its own batteries This is a set of two iDEAL mobile columns rated 36,000 lbs as a pair, ...

Product Description iDEAL MSC-13K-B-678 - a six-column mobile lifting set Synchronisation on this set is handled by a Siemens PLC working wit...

Product Description iDEAL MSC-13K-B-452 mobile column lifting set One technician can put this lift where it needs to go. Each column moves on...

Product Description iDEAL FP14KC-X: a 14,000 lb four-post you set up around the vehicles you actually work on Most four-post service lifts arr...

iDEAL IWA-60-8500-HD-K multi-axle 3D truck aligner No vehicle lift required. That single line is the whole proposition of this system: it is ...