For more detailed information and guidance, you can download the following:

• Download Brochure (PDF)

Champion HRV15F-12: 50 CFM of air on a tank low enough to live under a mezzanine

The number that should decide this purchase is 50 CFM. That is the air budget the HRV15F-12 gives you, and it is the largest in the RV-series range we stock — enough to keep several high-draw tools working at once rather than taking turns at the tank. The 15 HP motor is how it is produced; the CFM figure is what you actually spend.

The second decision this model makes for you is orientation. The 120-gallon receiver lies horizontally over a 72.5" run, so the machine is long rather than tall. If your building's limiting dimension is overhead — a mezzanine, a duct run, a low bay — this is the version of the RV package that fits.

It arrives as a packaged simplex unit, which is the part buyers underestimate: the magnetic NEMA 1 starter is mounted and the control is a tank-mounted start/stop pressure switch, so what lands on your floor is a machine to connect rather than a kit to assemble.

How to spend 50 CFM

Air is the one shop utility people buy by horsepower and then run out of by volume. The useful exercise before you order is to add up what you actually run at the same time: an impact wrench, a die grinder, a sander, a blow gun and a tyre machine do not each draw their catalogue figure continuously, but two grinders and a sander genuinely do. A 50 CFM supply at 175 PSI is a multi-station number — it is why this model turns up in busy service shops and fabrication bays rather than one-man garages.

The 120-gallon receiver is the other half of that story. Tank volume does not create air, but it absorbs the peaks, so the pump cycles less often and the pressure at the far end of the shop stays flatter when three people reach for a tool at once.

An 1,800 RPM motor and a pump that turns slower than it does

The motor runs at 1,800 RPM and drives the RV30 pump through an enclosed belt guard. That belt is not just a coupling: it is a reduction, and the manufacturer's sheet records the pump turning considerably slower than the motor that drives it. A slow-turning pump sees fewer piston reversals per hour of running for the same delivered air, which is the single largest influence on how long a reciprocating compressor lasts — and it is also why belt-driven industrial units sound different from the direct-drive machines sold for home garages.

Loadless starting is fitted, so the motor starts against a vented head rather than a pressurised one. On a 15 HP motor that difference is the whole inrush characteristic, and on a shared panel it is what keeps the lights from dipping every time the compressor cuts in.

Will It Fit?

• Length. 72.5" along the wall, with air on all sides — a reciprocating pump is air-cooled, and a compressor jammed into a nook runs hotter than one with room to breathe.
• Height. Our data holds an overall height for this unit as a bare number with no unit recorded next to it. We will not print a clearance figure we cannot stand behind — ask us and we will confirm it from the factory drawing before you plan around a beam.
• Electrical service. The sheet lists this unit for 208 / 230 / 460 / 575V three-phase supply. Which of those you are getting is an order-time decision, not a site-time one, so confirm it with us and with your electrician before the machine ships.
• Weight and handling. 1,017 lbs. Plan the offload and the route to its final position before delivery day.
• Air connection. 3/4" tank outlet. Size the shop main to the tools, not to the outlet.
• Your responsibility. Slab, supply, permits, offload and placement are the buyer's to arrange.

Perfect For

• Multi-bay service shops where several technicians pull air simultaneously all day.
• Fabrication and welding shops running plasma, grinders and blast equipment.
• Buildings with an overhead constraint that rules out an upright receiver of the same volume.
• Operations that want it wired, not assembled — the starter and controls arrive fitted.

What's in the Box

A packaged simplex unit built around the RV30 pump: the 15 HP motor, the horizontal 120-gallon ASME coded receiver, a mounted NEMA 1 magnetic starter as standard, tank-mounted start/stop pressure switch control, an intake filter and silencer, an enclosed belt guard and loadless starting. No air dryer is fitted and no electronic drain valve is fitted — both are worth raising before you order if your air quality or your maintenance routine depends on them.

Specifications

A note about the air delivery figure

Our catalogue rates this unit at 50 CFM and that is the figure printed above. It is worth knowing that the manufacturer's own specification list gives two lower delivery figures instead, measured at 125 PSIG and at 175 PSIG, and records both without a unit written beside them — so we can tell you the sheet is more conservative than the headline, but we cannot responsibly print its numbers as air delivery. If your tool load sits close to the limit, that gap is exactly where a shop runs short of air, and it is worth asking us for the factory data sheet in writing before you commit.

Certification, stated plainly

The feature list for this model states an ASME coded receiver, and notes that the coding does not extend to base-mount versions of the same package. It also states that the receiver is compliant with California code. Beyond those two, our data claims no third-party safety listing for the packaged machine, so none is claimed here. If your insurer, your fleet policy or your local inspector requires a specific listing on shop pressure equipment, ask us to confirm in writing what documentation ships with this unit before you order.

Shipping and delivery

Freight to the lower 48 states, priced live at checkout because carrier rates move. At 1,017 lbs crated this is a forklift or dock delivery; if you have neither, arrange terminal pickup from the carrier, which is a normal and often simpler choice on a machine this size. Residential addresses carry a residential fee. Before you sign anything, walk the shipment: look along the receiver for dents, check the pump, motor and starter enclosure for impact, and write any damage on the delivery paperwork while the driver is still there. A clean signature is very difficult to argue with afterwards.

Warranty

Our record for this model points at the store's warranty claims page without stating a term, so no length of cover is printed here — ask us for the current manufacturer terms in writing before you order. Whatever they are, protect them the same way: if the machine develops a fault, call before you open anything. A pump or starter stripped down ahead of the claim is the commonest reason a good claim fails.