BelAire 4916V — the 60 Gallon That Fits Under a Low Ceiling
The reason to choose the 4916V over its taller siblings is height. It stands under 70 inches — 69.7" to the top — which puts it below the level where a garage door track, a low joist or a run of conduit starts making the decision for you. In a basement shop, a residential garage or a converted unit with a suspended ceiling, that is not a detail; it is the whole question.
Everything else is conventional and solid: a 5 HP motor on 230V single-phase power, a belt-driven solid cast iron pump, stainless steel valves and a 60 gal vertical ASME tank, all at 250 lbs.
Will It Fit?
| Dimension |
Figure |
| Height |
69.7" — under 70 inches |
| Length |
22.9" |
| Width |
27.2" |
| Weight |
250 lbs |
Measure to the lowest thing above the spot you want to use rather than to the ceiling itself, and remember the machine needs clearance above it for the discharge plumbing and for a hand on the fill cap. On the floor it wants a flat concrete slab; at 250 lbs on a compact base it is the lightest of the vertical machines here, but that mass is still concentrated on a small area. The route in matters as much as the destination — check the doorway. Confirming clearance, doorways and the circuit is the customer’s responsibility before the truck is booked.
Electrically it is 230V, 1-phase, on a 40 amp circuit, with no magnetic starter fitted. Have an electrician confirm the supply and the breaker before you order.
What 165 PSI Means for Your Tools
This pump tops out at 165 PSI, a little below the ceiling of the larger two-stage machines in the range, and delivery at maximum pressure is around 14 CFM. For the overwhelming majority of shop work that is irrelevant — impact guns, ratchets, blow guns and sanders are specified well below that, and the reserve above their working pressure exists to stop pressure sagging while the tool is running. It matters only if you have a specific tool with a high working-pressure requirement, in which case check its plate before you buy rather than after.
The more useful way to think about a 60 gal tank on a 5 HP pump is duty rather than pressure. Air tools that draw continuously — a DA sander, a media blaster — will run the tank down and keep the motor working. Tools used in bursts will barely trouble it. Tank volume buys you burst capacity, not endless air.
Delivery at 100 PSI: Two Published Figures
This product’s own data gives two slightly different numbers for the same measurement, and rather than average them we will show you both:
| Delivery at 100 PSI |
Source |
| 16 CFM (approximately) |
The product overview on this page |
| 16.1 CFM |
The feature list, and the pump CFM spec field |
The gap is small and unlikely to change anyone’s tool list, but a published figure should be one number. A second disagreement in the same data is worth more of your attention: the title and the description call this a two-stage pump, while a spec field records it as single stage. That does affect what the machine is. If either figure is load-bearing for you, ask us in writing before you order and we will confirm both against the factory spec sheet in writing.
The Parts That Wear
Stainless steel valves, a solid cast iron pump and a belt drive are the three choices that decide how long a compressor lasts. Stainless valve plates survive the constant hot cycling that kills cheaper steel ones. Cast iron carries heat out of the cylinder and wears slowly. Belt drive lets the pump spin slower than the motor, and a slower pump is a cooler, longer-lived pump — and a belt is a consumable you can replace in an afternoon, unlike a seized direct-drive assembly.
Lubrication is splash with an oil level sight glass. There is no aftercooler and no dryer, so open the manual drain daily and treat the air downstream if you are spraying.
Perfect For
-
Low-ceiling garages and basement shops — the reason this model exists.
-
Home mechanics with a dedicated single-phase circuit who want cast iron rather than an aluminium hobby pump.
-
Small trade shops using air in bursts rather than continuously.
-
Not for a high-consumption production bench. A 60 gal reserve and one 5 HP pump is a small-shop combination.
What’s in the Box
The compressor arrives assembled on its 60 gal vertical tank with the cast iron pump, stainless steel valves, fully enclosed high-flow belt guard, oil level sight glass, start-stop pressure switch control, pressure gauge, air filter, ASME safety valve and manual tank drain. Every unit is 100% factory tested at full pressure. No dryer, no regulator, no magnetic starter and no electronic drain valve are included; the tank outlet is 1/2".
Certification, Stated Plainly
The tank carries the American pressure-vessel code stamp and ships with a matching safety relief valve. That is a certification of the vessel — how it was designed, welded and inspected — and it is not the same thing as a third-party safety listing of the complete electrical machine. Some insurers and some local jurisdictions ask for a listed assembly by name. If yours is one of them, ask us in writing before you order and we will give you the answer in writing.
Shipping and Delivery
Compressors of this size travel by freight truck within the lower 48 states rather than by parcel carrier. This one is the easiest of the range to receive: 250 lbs and 69.7" tall. Your freight cost is quoted live at checkout against your own address. Delivery to a home address carries a residential fee; picking the machine up from the freight terminal yourself avoids it.
Decide how the crate comes off the truck before it arrives — that part is the receiver’s responsibility, so you want a forklift, a dock, or several people and a hoist ready. Inspect it with the driver while he is still there: shroud, belt guard, gauges, tank shell, and the pallet itself. Anything you find goes on the delivery paperwork before you sign. A note on the paperwork starts a freight claim; a clean signature usually ends one.
Warranty
A 2-year factory warranty is the published term, with the warranty document available on this page. If a component fails, do not disassemble it before the claim is opened — the manufacturer is entitled to inspect the failed part in the condition it failed, and a stripped pump is the single most common reason a legitimate claim gets turned down. Call us and we will open it with you.
